I plan to add front fog lights to my V90cc 2020 Sensus (originally there weren't any). I saw that there is a wiring harness behind the bumper to connect. 
Does anyone know if I need to additionally activate the halogens if I connect them? If so, will Orbit be enough for this? 
Is there any options in the Sensus menu to control the front fog lights?

Hi Guys,

I am new to this forum and sorry if this question repeats, but I could not find the answer. OK let start from beginning. I have Volvo XC40 2021/2022 - CEM - 32268108 AB -> SPC 5748G (Power Arch) on my garage bench, but I believe this same CEM goes to XC60 and others. I am trying to connect to this CEM via CAN bus and play around just for my curiosity. Straight away I have faced the issue.

OK let explain, what I did and trying to do. I found on internet this electrical wiring manual MC-10236765-9999.pdf and figured out that I need use those pins to connect to power it the CEM:


NOTE: because of thread has limitation I have to split my message in parts.

Attached Files

Thumbnail(s)
           

Hey guys
Can someone share the DEFAULT config for Volvo C40 Recharge Twin which origin is Europe?
I own C40 from US and want to tweak a couple of things, but it would be great to have an initial configuration for EU car.
Many thanks!

I was browsing through the list of options available in orbit and was planning to make a few changes, but a few caught my eye. Has anyone had any experience with changing the following?

• 504. TRAFFIC LIGHT ATTENTION 
  
• 494. HIGHWAY ASSIST
  
• 493. EMERGENCY LANE OCCUPIED WARNING
  
• 317. EVASIVE MANOUEVRE ASSIST
  

I have an early 22 XC60 PE, Canadian spec, so it has the full LED bending(low beam) lights. What are you folks finding are the best settings ?  Stock now, I find it way to sensitive to turning off highbeams , from porch lights, street lights etc. I have read through a bunch of posts, but most seem to be trying different settings due to not having the full LED lights.

Hello,

My car has issue with parking sensors, on cluster shows: park assistance temporarily unavailable and front, end sensors are not working.

I checked DTC, but no relevant codes appear.  Checked auxiliary battery (which was installed new 1 month ago) looks good. Start/stop function works properly. Installed WAM module (was dead) calibrated cameras,  but still sensors doesn't work. Any other suggestion how to start parking sensors to work?

Car: 2017 XC90 T6

Hi! New here. Just ordered me a cable and waiting for the pin. Just wanted to ask, what do I need to do before I can start to configurate my car? I mean, do I just plug in the cable, turn my car on and just log in etc? Does the car need to be running or just power on? Do I need to put it in some "active mode", or select something from the census menu? My car is 2019 V90 T8

My car is XC90 T8 2022late, The original car have no drive mode knob, and i change the hardware including DRIVE MODE KNOB (pic 1), and use orbit changing item 057,  from "03 with glass bottom switch in CSD "to "02 with drive mode switch ",  and item 452, from "01 no drive mode knob/switch" to "02 with drive mode knob/switch/regulator "(pic2),   after loading these two settings ,there is  a SUM fault light in the driver screen (pic 3), What is the problem?

Attached Files

Thumbnail(s)
           

My car is XC90 T8 2022late, i change DRIVE MODE using  knob (pic 1), and use orbit changing item 057,  from "03 with glass bottom switch in CSD "to "02 with drive mode switch ",  and item 452, from "01 no drive mode knob/switch" to "02 with drive mode knob/switch/regulator "(pic2),   after loading this two settings ,there is  a SUM fault light in the driver screen (pic 3), What is the problem?

Attached Files

Thumbnail(s)
           

Hi,

I have 2018 XC60 II, with basic seats (electric height and backrest adjustment) without heating.
I replaced it to basic seats, but with heating.
Which pins do I need to connect?

Thank you.