| Welcome, Guest |
You have to register before you can post on our site.
|
| Forum Statistics |
» Members: 2,935
» Latest member: gigo42
» Forum threads: 832
» Forum posts: 6,472
Full Statistics
|
| Online Users |
There are currently 142 online users.
» 3 Member(s) | 136 Guest(s)
Bing, Google, Yandex, azndonx, cron808, juzzmee
|
|
|
| ICUP upgrade risk from manufacturer? |
|
Posted by: uuuuu5 - 11-29-2024, 03:06 AM - Forum: OrBit Q&A - Ask your questions here!
- No Replies
|
 |
I used the software to change the factory default settings, in such a state, go to the 4S shop to upgrade the ICUP model car machine system version, is there a big risk of being locked in the car? Or try to restore the factory settings before upgrading? The area is China.
thx
|
|
|
| Couldn’t Fast Charge… Orbit Saving my Bacon |
|
Posted by: Pranner - 11-27-2024, 10:38 PM - Forum: Service Functions
- No Replies
|
|
Wasn’t able to DCFC in the cold. Tesla NACS which usually worked well wasn’t having it. Stopped at 2 Superchargers and nothing but error code. Then I slow charged enough to get to a Jule unit. Again, Error Code!
That’s when it dawned on me the problem may be the car. So happy I keep my laptop and OBD2 connector in the car. Did a hard reset on all ECU’s with anything to do with the battery. Culprit may have been OBC, but I just went the safe route and hard reset them all.
It worked! Orbit is a must have for out of warranty BEV’s! Thanks!
|
|
|
|
| ECU command FAILED when trying to set egress seat offsets |
|
Posted by: hexaust - 11-25-2024, 08:26 PM - Forum: Misc
- Replies (6)
|
|
I’m getting the following logs when trying to set the egress seat offsets:
Code: Sending seat offsets write
ECU command FAILED!
Error Reason: Error setting diag session on the ECU
I’m trying this on a XC40 from 2019, the default value that is shown is 0000. I changed the 245 EASY INGRESS EGRESS to 03 With easy ingress egress retracting.
|
|
|
|
| Adding massage and ventilation |
|
Posted by: danwink - 11-24-2024, 07:26 PM - Forum: Retrofitting
- Replies (4)
|
|
Hi all-
I am wondering if anyone can help me to identify seats to swap into my 2019 S60 T6 Inscription.
The interior is Almond and seats are heated.
I would like to add both ventilation and massage as I frequently commute long distances.
I did see the process for adding massage requires a wire to be run.
Two questions.
1. What models share the same seat?
2. How to identify seats with massage? If I’m looking at a salvaged vehicle, is there a way to know if they have massage if the car does not power on?
|
|
|
|
| 155. SPEED WARNING |
|
Posted by: european - 11-23-2024, 03:50 PM - Forum: Speed Limit
- Replies (1)
|
|
Hi all,
I want to warn others with the config item 155.
After I set "155. SPEED WARNING" to "With speed warning for GSO" I got a warning every time I was above 120 km/h.
This is VERY annoying since it shows up also on the highway where the speed limit is 130 km/h. So irrespective of anything, if your speed is above 120 kph your are warned. The sign in the dashboard is an undocumented symbol.
I guess the "GSO" means something like "general speed xxxxxx".
I have a XC60 B4 MY22 and live in Europe. Hope this helps others!
|
|
|
|
| Error codes V60 |
|
Posted by: Machist - 11-23-2024, 02:22 PM - Forum: Service Functions
- No Replies
|
 |
Do anyone know these codes?
Check engine light is on.
I read
CEM:
B1497 - Ignition Extended Relay Control- General Electrical Failures- Circuit short to ground or open
B146F - Heated Nozzle/Heated Aquablades Front Supply- General Electrical Failures- Circuit open
ECM:
P20C9 - Reductant Control Module Requested MIL Illumination- Algorithm Based Failures- Event information
P2009 - Intake Manifold Runner Control Circuit Low (Bank 1)- -
NRCM:
P203B - Reductant Level Sensor "A" Circuit Range/Performance- FM (Frequency Modulated) / PWM (Pulse Width Modulated) Failures- No signal
|
|
|
|
|
