Hello everyone, I have a Volvo XC90 D4 from 11.2016 and my car did not come with front heated seats. I have the Inscription version with memory for both front seats and I want to know if I can activate heated seats in Orbit. I do not know if the seats are precabled and I need just to activate from software. Is anyone here who has activated heated seats? Thank you so much!
Hi, I have an X60 2022 with Android. The dealer in my country removed all Google Apps related from the car, no PlayStore, no Google Assistant, no Spotify, no Maps, nothing. The car basically useless in term of functionality that relied on Google.
Is there any way to put back Google Play Store to the car so that I can install Apps to use using OrBit?
I have already purchased the OrBit license and also has CEM and VGM PIN.
Hello, I would like to suggest setting up a chat on the forum, to facilitate conversations between each member and resolve any problem directly without disturbing other users of course.
What do you think of this, Administrators and members ?
Bonjour, je crée un nouveau sujet sur ce forum car j’ai un problème de décodage du code PIN CEM.
J’ai acheté Orbit pour les versions Sensus et décode le code PIN Cem
Cependant, je ne pensais pas qu’il était nécessaire d’utiliser VIDA Officiel pour extraire les LOGs et ensuite les étudier en orbite
J’ai utilisé un VPN connecté au Canada pour accéder au site *****CarBook***re, cependant il m’est impossible d’acheter l’abonnement car l’affichage du site me limite...
J’ai l’impression qu’il reconnaît que je suis basé en FRANCE
J’ai encore VIDA Official à installer mais je n’ai pas le compte validé avec l’abonnement.
Donc, si quelqu’un peut m’aider en utilisant le PC à distance avec votre compte pour extraire les journaux, je peux les payer pour ce service si nécessaire
Ou s’il y a une autre solution qui m’intéresse, merci
Désolé si ce n’est pas le bon endroit pour poser ce problème.
My car is 2020 V60 T4 with an 8 inch screen and only the Polestar mode has RPM display. So I use individual mode to get the best combination for me. Is there any way to set individual mode as default drive mode or just change the default comfort mode setting?
I'd like to change POWER STEERING to HIGH, the Dashboard to Polestar.
Thank you for such a nice tool for configuring and service new volvo cars. I have a Volvo XC40 and Orbit works amazing in all questions related to the car configuring.
I have one problem. Orbit always reports oil level equals to 0 mm. You can see it on the attached screenshot. I tried to run "Oil Level Reset" but I got these logs:
Code:
Starting Oil Level reset
ECU command FAILED!
Error Reason: Error in response from ECM
Could you please help me to solve this problem? I'm using the latest OrBit version. But I had the same problem on the previous versions.
**updated Feb 2025** When you write config to the car, or otherwise flash a module with software using OrBit, it may fail and you will see some errors in the screen console. But some issues depend on the computer or other things outside of what OrBit can control. Here are some typical errors and fixes for troubleshooting:
(Note: I want to clarify since it seems people mention this often when flash fails, "it doesn't work when I change XX setting"...it doesn't matter which config settings you are changing. That has no effect on the flashing process, whether it is successful or fails. The programming process does not care what the contents of the data are, it either works or it doesn't)
If Write Config, Restore to OEM or other software flash fails and you see any of the following messages in the screen log in OrBit:
Error reconnecting to the gateway after programming mode request
Gateway network not returned in time, update network card drivers and turn off power save settings?
Gateway (VCM/TCAM) did not return in time from prog mode boot request!
Follow the below steps to address some known issues that can cause this problem
For Sensus cars, try resetting the VCM gateway with OrBit:
In OrBit, connect to the car
Switch to the ECU Tools tab
Change the Active ECU dropdown to VCM
Click the "Reset ECU" button
There is no harm in resetting an ECU, it is equivalent to rebooting your PC
Wait for OrBit to reconnect after resetting the gateway ECU
Try write config/flash again and see if it succeeds
For AAOS cars, try resetting the TCAM gateway in the car:
In the car, push the front defogger button on the climate control, hold for 10-20 secs until the "SOS" button in the overhead console flashes
Release the front defogger button
Wait a few minutes, try to connect to the car with OrBit
Try write config/flash again and see if it succeeds
If the "SOS" button does not flash when trying the TCAM reset, the TCAM is not responding, move on to the battery reset
...If restarting the gateway does not resolve the problem, perform a battery reset:
Disconnect the negative terminal from the 12V battery
Wait a minute
Reconnect the negative battery terminal
Try write config/flash again and see if it succeeds
...If the battery reset does not resolve the problem, look at the local computer for possible issue, first rule out a firewall issue:
Disable the Windows Defender Firewall temporarily
Try write config/flash again and see if it succeeds
If you have a 3rd party AV program with firewall function, you will need to check vendor specific information to temporarily disable the firewall function
...If the firewall disable does not solve the problem, check network card driver power settings in Windows:
Open "Device Manager" in Windows
Expand the "Network adapters" node
Find the wired adapter, this should have "ethernet" in the name (example below)
Right click the adpater and choose "Properties"
Switch to the Power Management tab (if present)
Uncheck the box to allow the computer to turn the device off
Switch to the Advanced tab
In the advanced tab there is a list of "features" on the left and the "setting value" dropdown on the right
Look through the list of features and find the "power saving" type settings, and disable them, these can be a cause of problems for automotive diagnostics. Below is a list of the known settings that could be a problem. Disable these features if present:
Energy Efficient Ethernet
Link Speed Battery Saver
System Idle Power Saver
Ultra Low Power Mode
Selective Suspend
Force Suspend
Green Ethernet
Suspend AutoDetach
When done, click "OK" and close Device Manager.
Disconnect OrBit if it is connected
Remove and re-plug the OBD end of the VOE adapter to the car
Connect to the car in OrBit
Try write config/flash again and see if it succeeds
...If flashing still fails, other things you can try:
reboot the computer
check for network card driver updates in Windows optional updates (or specific to the computer vendor or network card manufacturer)
Uninstall and reinstall OrBit
If you have another compatible computer avaialble, try installing OrBit and write a config
...If all else has failed to resolve the issue, you will probably want to contact support-at-spaycetech.com by email and we will take a closer look at your specific issue.
Hello everyone, I am new to this forum in order to change the configuration of my new Volvo vehicle.
I took the plunge by leaving Audi ?.
I am looking for some information to activate the ACC of my vehicle, it has intellisafe assist and I would like to know if the ACC only uses the camera on the windshield or you have to have the radar in the grille of the vehicle for it to work ?
