Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Tire pressure sensors
#91
Still haven't checked. LOL Calibrated the thing another 20 times, but also driving the wife's car a lot right now.
Reply
#92
(08-13-2025, 02:55 AM)juzzmee Wrote:
(07-04-2025, 12:56 AM)BorD Wrote:
(03-03-2025, 09:27 PM)richardGG24 Wrote:
(01-29-2025, 12:20 AM)BorD Wrote: Autel TS 508WF reads all sensors and shows ID they came with. yet it can't programm V90CC, when selecting any Volvo that use the same type of sensor 2016 or 2019.
Think Autel needs to know PIN for that, so I'd try to use OrBit to write IDs collected by Autel or any ID I'd created. 
Issue seems to be with ID format, as car needs value in Hex and OrBit fails to write all variations I came up with. 
 I need to know how many digits ID should by according to Volvo, so I can create simillar IDs.

Can't program the TPMS system with Autel directly. IIRC autel default to read the sensor ID in Dec, and Orbit take sensor ID in Hex, you need to convert Dec to Hex. Idk if the smaller Autel TPMS tool can do this, but there is a drop down menu in my MS906PRO-TS that will show you Hex instead of Dec.

Finally was able to figure out what was the problem with wagon always showing "Calibrate" button greyed.
Updated all software using VIDA and reenabled TPMS once again. that time "Calibrate" was activated and clicable to do calibration. 
Conclussion: before direct TPMS can be enabled in configuration OrBit should check if software currently loaded to CPU is capable of that functionallity.

Hi,

I've installed BHsens sensors and successfully activate TPMS vis Orbit with all the recommended settings.
The calibrate button is greyed out and TPMS symbol flashing in the dash until stable TPMS symbol.
Tried programming the sensors with different IDs (seller provided TPMS programming tool) but no matter which IDS i set, the calibrate button is greyed out and unable to calibrate.
Can someone point me in the right direction where and what went wrong and what I should or can do to enable the calibrate button?
At wits end here and on the verge of removing the sensors.
TIA!
Guys,

Anyone? Really need some inputs. Until now still haven’t been able to get the calibrate button to work.
Reply
#93
Finally played around a bit. Connected to Orbit. 
Sensors all have values listed. 
Reset TPMS to Indirect. Turned car off and on, wheels were green. Did not store pressure.
Reconnect. Set back to Direct. Calibrate. Drove around. Spinny circle ran for about a minute. Got the message "Calibration complete". RR sensor still showing problem but this time no values listed. Assuming they may have just shown up after a restart, but just reconnected Orbit and went back to Indirect. Stored Pressure and drove around. Took 5 minutes.
All green. 

Ill leave it like this for a week and try again. Unless anyone has any other ideas.
Reply
#94
(04-27-2023, 06:05 PM)Power6 Wrote: 今天正在安装我的新轮胎和轮毂。或者等店里来的时候再安装。TPMS 传感器正在安装中。我会尽快确认它是否有效,实际上我们知道它可以工作,其他人也这样做了。我会确认我用过的 Velospinner 传感器是否有效。

注意:如果购买传感器,我认为它们必须与你的遥控钥匙的频率相匹配。因此,433Mhz 钥匙扣意味着你需要 433 MHz 传感器,315MHz 也是如此。美国 SPA 沃尔沃汽车是 433 MHz。当然,如果不购买通用传感器,它们需要与沃尔沃汽车兼容。我寻找非通用传感器,因为它们更便宜,不需要任何工具来设置它们。在美国,2016 款 XC90 配备了 TPMS 传感器,因此你可以寻找与之兼容的传感器。请记住,这仅适用于 Sensus,AAOS 不支持 TPMS 传感器系统。
i want to know ,the polestar 2(AAOS) has no chance to use tire pressure display?
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)