HP to HK Sound: Door Wires

[Power6]

hi.  I have an amplifier that I bought from a Volvo xc40, amplifier number 32265284AA, on which 5 channels worked.  front door, rear door, center speaker.  after installation only the front door goes in my car.  nothing more.  028 configuration for premium sound is enabled via orbit, I don't understand why it doesn't work on my car when the amplifier has the 5 channels in it.  I can't move anymore.  I've been doing just that for a month and I've already tried everything.  also 451 all options also 466 configuration all options.  nothing no response.  still only the front speaker.  the door.

Can you read in OrBit, the ECU info for the AUD? Post back a screen of what you got. It's probably best to make sure the ECU info is up to date, before you check it, run "Update Profile" from the main Shortcuts tab in OrBit to read the latest from all modules.
   

As mentioned, the correct config is "02" for High Performance audio on Item 028. The other config items for speakers and audio are not used that I know on the SPA/CMA. You can set this easy in the Config Wizard
   

It seems it could be a question of the wiring in the car, I am not too familiar with the base vs. High perf audio, if there are speakers that are not powered by the external amp (AUD) in the base system, but are powered by the AUD in the higher level system, wiring changes may be needed. 

I probably missed it coming in late, the AUD is from an XC40, is that the same model you are swapping it to?

[Lukas]

ECU Info: AUD  W1XZ72BCL2189527 (last updated 2025/01/21 11:12:52)

Assembly part: 32265284

Diagnostic part: 31456208

Harduare part: 31652394

Serial number: 90295410

Softuare parts: 32265285 AA

32200492 AA

Softuare details:

Total number of ECU Software Part Numbers: 02

SHLH: 32265285 AA

SUP1 Local Configuration Parameters: 32200492 AA

---

above is the diagnostics.  yes it's a volvo xc40.  setting 028 changed to 02. no change.  I try on the pins from the amplifier.  but no sound.  only for the front door l.

[Lukas]

I can't insert the picture

[Lukas]

I haven't installed the rear or center speaker yet.  for now I just want to get the sound from the amplifier output.  when the sound goes from the channels to the back and center, I will install them.

[Lukas]

IMAY2023 and Power6 do you know what to do next?

[IMAY2023]

Did you or did you not have an AUD under the passenger seat from factory? 
If you did not have the AUD but you have the harness unplugged, this means your IHU drives the speakers and the harness under the seat is not connected. You will need to rewire from the connector to the doors. 

If you had the AUD from factory,  what is the original part number and the new one?  what is your model / year and the donor car's model / year? 
Send a picture of the connectors under the passenger seat. 
You will need multimeter and an external audio source for testing and determining which pin goes to where.

If you provide your VIN number I might be able to check on VIDA to see what you have.

[Lukas]

YV1XZ72BCL2189527

---

hi.  the volvo had an amplifier connected under the passenger seat from the factory.  also turn on the connectors.  I'll send you a photo to your email because I can't insert photos here.  I will also send the number of the amplifier

[Lukas]

YV1XZ72BCL2189527

---

takže už môžem vkladať fotky

---

YV1XZ72BCL2189527

---

takže už môžem vkladať fotky

---

the
black cable serves as a sound tester

---

Pin 2.

---

this is the number of the amplifier I put in

---

Diagnostic

[Lukas]

---

F

[IMAY2023]

Something does not end up right with your existing wiring. 
The amp you replaced is the basic entry level amp which most likely same as you had from factory the only difference might be the model and loaded software on it. 
Connect the your test wires to C5 and C13. next to it.  That should be the left door speaker. 
I enclosed the wiring diagram.