Wireless Charger install on 2017

[Percy]

Hi!

I have now tested to program with button and it works fine for me. (As seen earlier in the thread i have retrofitted a new center console with charge in front of the gear selector, added LIN wire from CEM in my XC60 MY2020)

[Marcp]

Still WIP, tremendous amount of work to install the wireless charger - the whole centre console had to be taken out… There’re 2 screws that hold the trim around the cup holders that are only accessible from the buttom

Hi, good afternoon. Do I really need to remove the entire center console to install the charger?

[thermal-fixity]

Hi!

I have now tested to program with button and it works fine for me. (As seen earlier in the thread i have retrofitted a new center console with charge in front of the gear selector, added LIN wire from CEM in my XC60 MY2020)

Nice!

Really curious to know more about your experience, I've run the wire and coded but my charger does not work. A couple of questions:

Nazsky786:
CEM. FL 41
 Brown Connector Large.
If you have IHU 3.2 you can enable the on off switch option in Orbit and it will display a wireless charging icon. 
Pin is normally there, some work, some dont.

1. Is this the wire you ran? Anything else needed?

2. What options did you code?

---

Still WIP, tremendous amount of work to install the wireless charger - the whole centre console had to be taken out… There’re 2 screws that hold the trim around the cup holders that are only accessible from the buttom

Hi, good afternoon. Do I really need to remove the entire center console to install the charger?

yeah, that was my experience. I don't think there is a way around it

[Marcp]

Hello,

I’ve installed the wireless charger, but it’s not working.

- I’ve taken the 12V supply from the old cupholder 12V socket (pin 1 positive and pin 5 GND).
- The signal from pin 6 has been connected to pin FL41 on the CEM.
- I’ve set parameter 366 to 04, and also tested option 02.

Do you have option 450 configured?

The button appears on the screen without any errors.

Could you give me any advice or tell me how you have it configured?

Thanks.

[Nazsky786]

Hello,

I’ve installed the wireless charger, but it’s not working.

- I’ve taken the 12V supply from the old cupholder 12V socket (pin 1 positive and pin 5 GND).
- The signal from pin 6 has been connected to pin FL41 on the CEM.
- I’ve set parameter 366 to 04, and also tested option 02.

Do you have option 450 configured?

The button appears on the screen without any errors.

Could you give me any advice or tell me how you have it configured?

Thanks.

If you are sure you have power and good ground at the charger, and also enabled the charger via Orbit, it should work. Only time it doesnt work is if the CEM module fitted to your car is the older version, in which case that would need to be replaced to support it. 

Most cars from 2018 onwards support the WPC so you may have no power at charger caused by blown fuse etc or the signal wire isnt seated correctly at the brown connector on CEM. If you get the part number of the CEM it can be checked.

[Marcp]

Hello,

I’ve installed the wireless charger, but it’s not working.

- I’ve taken the 12V supply from the old cupholder 12V socket (pin 1 positive and pin 5 GND).
- The signal from pin 6 has been connected to pin FL41 on the CEM.
- I’ve set parameter 366 to 04, and also tested option 02.

Do you have option 450 configured?

The button appears on the screen without any errors.

Could you give me any advice or tell me how you have it configured?

Thanks.

If you are sure you have power and good ground at the charger, and also enabled the charger via Orbit, it should work. Only time it doesnt work is if the CEM module fitted to your car is the older version, in which case that would need to be replaced to support it. 

Most cars from 2018 onwards support the WPC so you may have no power at charger caused by blown fuse etc or the signal wire isnt seated correctly at the brown connector on CEM. If you get the part number of the CEM it can be checked.

My CEM is part number 32254021.

How can I tell if it is compatible with the wireless charger?
The connections are correct and I have 12V.

Do I need to configure parameter 450?

[Nazsky786]

By any chance do you have build date on the CEM?

450 is unchanged, it does nothing.

[Marcp]

Hello everyone!

Sorry, I didn't get around to posting the solution so that it could help others.

In the end, my CEM was not compatible with the wireless charger.

My car has Sensus and a mechanical automatic gear shifter. There are 2020 models that still have Sensus but already come with the electronic gear shifter and the factory-installed wireless charger. In fact, I seem to remember seeing one with the mechanical gear shifter and a wireless charger.

If you install a CEM from a model that already has Android Automotive, it is not compatible.

In summary, my CEM is not compatible. The only solution would be to install a 2020 CEM with the same specifications as my car.

Honestly, it's not worth all the work just to add the wireless charger, although those of us who enjoy tinkering with these things will understand.

Finally, I'd like to thank @Power6 for all the help provided, as it wouldn't have been possible to install the new CEM without him.