Air Suspension Calibration

[jdhx]

Folks, need help with the measurement process as I am not sure if I am doing it correctly.

1. WHEN do I take the measurement 
     a) When the car is parked and turned off or does it need to be running in Comfort mode or something else?
     b) Or, when I initiate the calibration the car does some leveling action. Do I need to take it right after this?

2. HOW do I take the measurement ACCURATELY?
    a) I tried with a metal measurement tape but I can imagine the numbers can be quite off if I am slightly off center and/or the not square from the ground. Hoping there's a better to way that is more accurate.
    b) Does the car need to be on flat even surface? My garage and driveway has a considerable slope and I am not sure if the car is leveling itself to compensate for it.

1. After the calibration process has started and it ask you what the measurements are.  That is because the process puts the suspension into a known state.

2. I do the measurements in two stages.  Before I start the calibration I measure the top of the disk in the centre of the wheel to ground (x) and the diameter of the disk (y).  Then when the calibration process asks for the values I measure the wheel arch to ground (z).  The value I input is z-x+y/2.  I do it this way because it is easier to measure from solid ground upwards than to measure wheel arch to centre of wheel.  Of course y does not vary and x only depends on temperature so will not vary much.  The car does not need to be on absolutely flat even ground but the more flat and even the better.

Well you did ask!

[chess]

Folks, need help with the measurement process as I am not sure if I am doing it correctly.

1. WHEN do I take the measurement 
     a) When the car is parked and turned off or does it need to be running in Comfort mode or something else?
     b) Or, when I initiate the calibration the car does some leveling action. Do I need to take it right after this?

2. HOW do I take the measurement ACCURATELY?
    a) I tried with a metal measurement tape but I can imagine the numbers can be quite off if I am slightly off center and/or the not square from the ground. Hoping there's a better to way that is more accurate.
    b) Does the car need to be on flat even surface? My garage and driveway has a considerable slope and I am not sure if the car is leveling itself to compensate for it.

1. After the calibration process has started and it ask you what the measurements are.  That is because the process puts the suspension into a known state.

2. I do the measurements in two stages.  Before I start the calibration I measure the top of the disk in the centre of the wheel to ground (x) and the diameter of the disk (y).  Then when the calibration process asks for the values I measure the wheel arch to ground (z).  The value I input is z-x+y/2.  I do it this way because it is easier to measure from solid ground upwards than to measure wheel arch to centre of wheel.  Of course y does not vary and x only depends on temperature so will not vary much.  The car does not need to be on absolutely flat even ground but the more flat and even the better.

Well you did ask!

Thanks, will try this method with my new laser measure.

[bowditchsmith]

Been enjoying orbit for the past month to add some nice creature comforts to our XC90. I am very interested to try out this suspension calibration vs making the switch to Ghostlink Adapters. is anyone actively using orbit to lower their vehicle? The majority of the thread looks like trial and error, with - 30mm being stated as being to harsh / aggressive.

is - 20mm the sweet spot?

EDIT: Update - I just went out to the car to take measurements of the stock suspension in preparation for playing around with the settings, and noticed that my DSF height is slightly lower, and it being compensated by a slightly raised PSR height.

Measured heights from ground to wheel arch:

• DSF - 32.375" (822.3mm)
  
• PSF - 32.75" (831.8mm)
  
• DSR - 32.75" (831.8mm)
  
• PSR - 33" (838.2mm)
  

There doesn't seem to be any leaks, and it reports the discrepancy when connected to the calibration. 

A bit unsure with how I should address. Should I first adjust them all to be the same ride height in Orbit?



I just ordered a Metric tape measurer so that I can stop dealing with these conversions and risk of inaccuracies.

[brunopbarbosa]

Hi All, i have a question related with the air suspension settings - on the Volvo repair procedures for the V90, when it comes to replacing the air springs for those with air suspension, it mentions a section where before removing the springs you must deflate them using VIDA.

Is this something that can be done with OrBit as well?

[NetMare]

Thanks @Power6!
Can somebody confirm or test that the VGM pin is needed for "just" adjusting the air suspension height on an iCUP model?
It's a leased company car and it will be chaged every 2-3 years. Just want to make this one modification

Hi guys...
could anyone test if the suspension calibartion procedure is possible without the VGM pin?