+- OrBit Forums (https://forums.spaycetech.com)
+-- Forum: Configuration Items (https://forums.spaycetech.com/forumdisplay.php?fid=3)
+--- Forum: Lights (https://forums.spaycetech.com/forumdisplay.php?fid=4)
+--- Thread: Bending Lights and Active High Beam (/showthread.php?tid=7)
RE: Bending Lights and Active High Beam - IMAY2023 - 07-02-2024
(07-01-2024, 08:55 PM)paunionutz Wrote: Hello guys. I just swaped my headlights with ABL. Everiting is working, but i notticed 2 problems:
1. I see shadow spots on the road from bouth headlights. Light is not uniform
2. When i have a car in front, i don't have light in the center, i bearly see something.
I din't config correct?
It's not the config, you need to realign your headlights after replacing.
There are two screws on each headlight (up and down) and (right to left).
RE: Bending Lights and Active High Beam - paunionutz - 07-02-2024
(07-02-2024, 01:00 AM)IMAY2023 Wrote:I already did that, before i test them, on the headlight device at TUV station(07-01-2024, 08:55 PM)paunionutz Wrote: Hello guys. I just swaped my headlights with ABL. Everiting is working, but i notticed 2 problems:
1. I see shadow spots on the road from bouth headlights. Light is not uniform
2. When i have a car in front, i don't have light in the center, i bearly see something.
I din't config correct?
It's not the config, you need to realign your headlights after replacing.
There are two screws on each headlight (up and down) and (right to left).
RE: Bending Lights and Active High Beam - Pau1ey - 07-02-2024
(07-02-2024, 03:24 AM)paunionutz Wrote:(07-02-2024, 01:00 AM)IMAY2023 Wrote:I already did that, before i test them, on the headlight device at TUV station(07-01-2024, 08:55 PM)paunionutz Wrote: Hello guys. I just swaped my headlights with ABL. Everiting is working, but i notticed 2 problems:
1. I see shadow spots on the road from bouth headlights. Light is not uniform
2. When i have a car in front, i don't have light in the center, i bearly see something.
I din't config correct?
It's not the config, you need to realign your headlights after replacing.
There are two screws on each headlight (up and down) and (right to left).
Which of these did you choose for 109 ACTIVE HIGH BEAM?:
04 With AHB2 (Adaptive), Low Beam in Village
05 With AHB2 (Adaptive), High Beam in Small Village
We're using setting 04 on both XC90 & XC60 after trying and not liking 05 which had that dark gap when following a car.
RE: Bending Lights and Active High Beam - paunionutz - 07-02-2024
(07-02-2024, 04:18 PM)Pau1ey Wrote:(07-02-2024, 03:24 AM)paunionutz Wrote:(07-02-2024, 01:00 AM)IMAY2023 Wrote:I already did that, before i test them, on the headlight device at TUV station(07-01-2024, 08:55 PM)paunionutz Wrote: Hello guys. I just swaped my headlights with ABL. Everiting is working, but i notticed 2 problems:
1. I see shadow spots on the road from bouth headlights. Light is not uniform
2. When i have a car in front, i don't have light in the center, i bearly see something.
I din't config correct?
It's not the config, you need to realign your headlights after replacing.
There are two screws on each headlight (up and down) and (right to left).
Which of these did you choose for 109 ACTIVE HIGH BEAM?:
04 With AHB2 (Adaptive), Low Beam in Village
05 With AHB2 (Adaptive), High Beam in Small Village
We're using setting 04 on both XC90 & XC60 after trying and not liking 05 which had that dark gap when following a car.
I use 05. I'll try 04 to see how is it. Thanks
Bending Lights and Active High Beam - anandsai.mishra@gmail.com - 07-06-2024
You have pixel led headlamps what you are noticing is matrix led headlights
Sent from my iPad using Tapatalk
RE: Bending Lights and Active High Beam - Joe558 - 07-06-2024
Evening all. I swapped from US headlamps without bendy to EU bendy. I’ve tried a few different settings in orbit (various ahb settings, bendy on and off, and a slew of headlight types) but I’m consistently getting the below on both left and right hcm:
B15AD - Headlamp Control Module LED Channel 4- General Electrical Failures- Circuit open
I’m also getting this on the cem:
B14C2 - Head Lamp Input- Bus Signal / Message Failures- Invalid serial data received
Anyone have any thoughts ?
RE: Bending Lights and Active High Beam - IMAY2023 - 07-06-2024
(07-06-2024, 02:21 AM)Joe558 Wrote: Evening all. I swapped from US headlamps without bendy to EU bendy. I’ve tried a few different settings in orbit (various ahb settings, bendy on and off, and a slew of headlight types) but I’m consistently getting the below on both left and right hcm:Assuming you got the headlights with their controllers and they are correct side.
B15AD - Headlamp Control Module LED Channel 4- General Electrical Failures- Circuit open
I’m also getting this on the cem:
B14C2 - Head Lamp Input- Bus Signal / Message Failures- Invalid serial data received
Anyone have any thoughts ?
That usually happens when you choose the wrong headlight type with the wrong feature or the headlights are faulty. Post here the headlight stickers, easier to advise for correct type and feature.
RE: Bending Lights and Active High Beam - Joe558 - 07-06-2024
I got the headlights with the hcm on them, but had to replace one after the fact. With that said I got the files from support to reprogram them and took care of that.
RE: Bending Lights and Active High Beam - glennda5id - 10-12-2024
I have 2016 XC90 which did not come with an HCM headlights.
First question, to use adaptive do you need to turn on auto high beams?
Second, US cars by default do not remember "Auto High Beam: setting when the car is turned off.
My original config was 106::05 LED With Bending Light, type A, Top Range
Changes to
106::06 LED With Bending Light, type B, Top Range
Should this allow it to remember the setting? It doesn't seem to work.
Third: I have a 2021 XC40 BEV. It has bending low beams. It does not have Pixel lights. Does 109 Active High Beam, setting to adaptive do anything with this car?