Help 2022 S60 BLIS & TPMS

[vincent]

Please help, I  two problems in programming.
1、Added BLIS and changed option 152 to 02，But it doesn't work. Is there any other option that needs to be changed as well? 
2、TPMS does not display numerical values.
help me suggest something，Thank you!

[IMAY2023]

Regarding the BLISS, 
I don't know how you added the BLIND SPOT DETECTION MODULEs but it is not that simple. 
Having the connectors ready on the rear bumper harness does not mean that CAN bus from the rear bumper harness connector is indeed connected to the ACTIVE SAFETY DOMAIN MASTER ASDM and most likely it is not. 
In addition, BLISS system requires mirrors with BLISS too.  Without the BLIS mirrors it's just rear cross traffic alert. 

For the TMPS here is a specific thread on that topic.

[vincent]

TPMS is ok now,Thank you, the hardware and wiring harness required for BLIS have been installed, and the can protocol cable has also been connected. Orbit: 146:02152:02153:03317:02322:02, but there will be many errors that cannot work。
ASDM:
U21269 - Invalid Data Received in InhbOfAsySftyDecelByVehDyn- Component Failures- Performance or incorrect operation
U21273 - Invalid Data Received in EscSt- Component Failures- Performance or incorrect operation
U111A - Interrupted Communication with Side Obstacle Detection control Module Right (SODR)- -
U1119 - Interrupted Communication with Side Obstacle Detection control module Left (SODL)- -
U120B - Intermittent Communication Problem on Safety CAN Exposed- -

SRS:
U21286 - Invalid Data Received in RdyPostImpctBrkg- Component Failures- Performance or incorrect operation

[hao166]

TPMS 现在可以了，谢谢，BLIS 所需的硬件和线束已经安装完毕，可以协议线也已经连接。Orbit: 146:02152:02153:03317:02322:02，会有很多错误无法工作。
ASDM:
U21269 - InhbOfAsySftyDecelByVehDyn- 组件故障- 性能或操作不正确
U21273 - EscSt 中接收到无效数据- 组件故障 - 性能或操作错误
U111A - 与侧面物联网控制模块（SODR）的通信中断 - -
U1119 - 与第三方二次故障物检测控制模块 (SODL) 的通信中断 - -
U120B - 安全 CAN 暴露上的间歇性通信问题 - -

SRS :
U21286 - RdyPostImpctBrkg 中收到无效数据 - 组件故障 - 性能或操作不正确

您好，请问您的BLIS接线图可以分享一下吗？我也准备给我的21 S60加装BLIS系统，但是找不到线束的接线图。谢谢。21 S60加装BLIS系统，但是找不到线束的接线图。谢谢。

---

TPMS 现在可以了，谢谢，BLIS 所需的硬件和线束已经安装完毕，可以协议线也已经连接。Orbit: 146:02152:02153:03317:02322:02，会有很多错误无法工作。
ASDM:
U21269 - InhbOfAsySftyDecelByVehDyn- 组件故障- 性能或操作不正确
U21273 - EscSt 中接收到无效数据- 组件故障 - 性能或操作错误
U111A - 与侧面物联网控制模块（SODR）的通信中断 - -
U1119 - 与第三方二次故障物检测控制模块 (SODL) 的通信中断 - -
U120B - 安全 CAN 暴露上的间歇性通信问题 - -

SRS :
U21286 - RdyPostImpctBrkg 中收到无效数据 - 组件故障 - 性能或操作不正确

您好，请问您的BLIS接线图可以分享一下吗？我也准备给我的21 S60加装BLIS系统，但是找不到线束的接线图。谢谢。

根据我得到的信息，BLIS系统的安装需要添加雷达模块和线束，用警报灯代替参考板手册，雷达模块进行编程，将雷达模块的信息写入CEM中。我不知道这个信息是否正确，但仅此而已这里仅提供参考。

[vincent]

The wiring harness has been added, and blind spot rearview mirrors have been installed. I use used SODL/SODR units from another car.
There are still the following alarms, I'm not sure if the software needs to be reloaded
U111A - Interrupted Communication with Side Obstacle Detection control Module Right (SODR)- -
U1119 - Interrupted Communication with Side Obstacle Detection control module Left (SODL)- -

[IMAY2023]

either the used modules you got are faulty or your wiring has a short. 
Remove the modules and check the voltage on each CAN wire. Then connect 1 by one and check again.

[vincent]

either the used modules you got are faulty or your wiring has a short. 
Remove the modules and check the voltage on each CAN wire. Then connect 1 by one and check again.

Thank you, as per your suggestion, I will test each one again. May I ask you again? Do the following options need to be changed when BLIS is activated?
: 146:02
: 152:02
: 153:03
: 317:02
: 322:02

[IMAY2023]

 146 COLLISION MITIGATION SUPPORT FRONT :02  > This has nothing to do with BLIS. It uses the front facing camera behind the rear view mirror. 
152 BLIND SPOT INFORMATION SYSTEM :02 > This is the actual BLIS and cross traffic alert when reversing. 
: 153 COLLISION MITIG :03 >  My 2019 S60 factory settings was without. I put it to 02 and it works. It uses the BLIS sensor to detect cars coming from back in high velocity while your car is stand still. It applies full break and turns on hazard lights.  Not mandatory for 152.  
: EVASIVE MANOUEVRE ASSIST 317 > this one uses the  front facing camera behind the rear view mirror and the BLIS sensors to MANOUEVRE car when braking distance is insufficient and collision is inevitable.  I set it to 02 and it works. It detected the car on my right coming too close and it maneuvered the car to left to avoid collision from left side.    
: 322 CMS ONCOMING :02  >  This has nothing to do with BLIS. It uses the front facing camera behind the rear view mirror.  It detects and applies brakes if an idiot drives on your lane in opposite direction towards you like someone overtaking in opposite direction and ends up in front of you.  

[hao166]

TPMS is ok now,Thank you, the hardware and wiring harness required for BLIS have been installed, and the can protocol cable has also been connected. Orbit: 146:02152:02153:03317:02322:02, but there will be many errors that cannot work。
ASDM:
U21269 - Invalid Data Received in InhbOfAsySftyDecelByVehDyn- Component Failures- Performance or incorrect operation
U21273 - Invalid Data Received in EscSt- Component Failures- Performance or incorrect operation
U111A - Interrupted Communication with Side Obstacle Detection control Module Right (SODR)- -
U1119 - Interrupted Communication with Side Obstacle Detection control module Left (SODL)- -
U120B - Intermittent Communication Problem on Safety CAN Exposed- -

SRS:
U21286 - Invalid Data Received in RdyPostImpctBrkg- Component Failures- Performance or incorrect operation

How did you solve the TPMS problem? Did you replace the new sensor? Thank you.

[vincent]

 146 COLLISION MITIGATION SUPPORT FRONT :02  > This has nothing to do with BLIS. It uses the front facing camera behind the rear view mirror. 
152 BLIND SPOT INFORMATION SYSTEM :02 > This is the actual BLIS and cross traffic alert when reversing. 
: 153 COLLISION MITIG :03 >  My 2019 S60 factory settings was without. I put it to 02 and it works. It uses the BLIS sensor to detect cars coming from back in high velocity while your car is stand still. It applies full break and turns on hazard lights.  Not mandatory for 152.  
: EVASIVE MANOUEVRE ASSIST 317 > this one uses the  front facing camera behind the rear view mirror and the BLIS sensors to MANOUEVRE car when braking distance is insufficient and collision is inevitable.  I set it to 02 and it works. It detected the car on my right coming too close and it maneuvered the car to left to avoid collision from left side.    
: 322 CMS ONCOMING :02  >  This has nothing to do with BLIS. It uses the front facing camera behind the rear view mirror.  It detects and applies brakes if an idiot drives on your lane in opposite direction towards you like someone overtaking in opposite direction and ends up in front of you.  

Thank you, it's very clear. I'll try again

---

TPMS is ok now,Thank you, the hardware and wiring harness required for BLIS have been installed, and the can protocol cable has also been connected. Orbit: 146:02152:02153:03317:02322:02, but there will be many errors that cannot work。
ASDM:
U21269 - Invalid Data Received in InhbOfAsySftyDecelByVehDyn- Component Failures- Performance or incorrect operation
U21273 - Invalid Data Received in EscSt- Component Failures- Performance or incorrect operation
U111A - Interrupted Communication with Side Obstacle Detection control Module Right (SODR)- -
U1119 - Interrupted Communication with Side Obstacle Detection control module Left (SODL)- -
U120B - Intermittent Communication Problem on Safety CAN Exposed- -

SRS:
U21286 - Invalid Data Received in RdyPostImpctBrkg- Component Failures- Performance or incorrect operation

How did you solve the TPMS problem? Did you replace the new sensor? Thank you.

Add me on WeChat ID: Chengxy_1993