+- OrBit Forums (https://forums.spaycetech.com)
+-- Forum: Configuration Items (https://forums.spaycetech.com/forumdisplay.php?fid=3)
+--- Forum: Retrofitting (https://forums.spaycetech.com/forumdisplay.php?fid=13)
+--- Thread: Bliss and CTA (/showthread.php?tid=552)
Bliss and CTA - paunionutz - 08-10-2024
I managed to retrofit Bliss and CTA on my 2019 V60
Parts needed:
Complete mirrors (i don't have PN, but must have bliss led on it)
Rear modules, and brakets. I foud brakets with modules, and fore sure are from V60.
LH 31455672 + 32227721 + 32254967 and
RH 31455673 + 32227722 + 32254967
Rear bumper harness 31654287 (in my case with bliss, 6 parking sensors and foot movement sensor)
6 male pins for the body connector (y don't have PN, i already had the pins)
Now the wiring from the body (male connector)
PIN 2 (BU/OG) -12v from fuse no 30 in the trunk (here also require pin - i don't have PN)
PIN 19 (BK/WH) - ground
PIN 17 (WH) - A15 ASDM
PIN 18 (GN) - A5 ASDM
PIN 7 (WH) - A16 ASDM
PIN 8 (GN) - A6 ASDM
ASDM connector already has wires, you can tap it toghether with existing ones
With Orbit i set
152 : 02 and 153 : 03
I didn't drove the car yet, but i don't have any errors
Bliss and CTA - Sieluck - 12-27-2024
Hi.
Well done. Congrats on this retrofit. I'm considering this as well as a last retrofit for my car. I only have pdc sensors in the back. You said you have 6,yes? Does bliss or cta require 6 sensors?
Can you share the costs of parts for this entire retrofit?
ADSM... Where is that module located? You said cables are on this module. So you need to break into existing harness?
Lastly, do you have any pictures from this operation?
Wysłane z mojego CPH2581 przy użyciu Tapatalka
RE: Bliss and CTA - paunionutz - 12-31-2024
(12-27-2024, 09:23 AM)Sieluck Wrote: Hi.
Well done. Congrats on this retrofit. I'm considering this as well as a last retrofit for my car. I only have pdc sensors in the back. You said you have 6,yes? Does bliss or cta require 6 sensors?
Can you share the costs of parts for this entire retrofit?
ADSM... Where is that module located? You said cables are on this module. So you need to break into existing harness?
Lastly, do you have any pictures from this operation?
Wysłane z mojego CPH2581 przy użyciu Tapatalka
I don't know if it work with only 4 sensors in the back.
About the cost.... i don't know exactly. I jave a friend with a scrapyard, and he gived to me without money (i retrofited something on his car).
ASDM is the camera module behind the mirror
RE: Bliss and CTA - marinalin85 - 01-05-2025
I have BLISS and CTA from factory and only 4 PDC in the rear (+ 4 in the front) so it should work
Bliss and CTA - Sieluck - 01-05-2025
That's good news. However this retrofit, still being considered, will be very expensive to install. I'm not sure if this feature is actually worth the money that need to be spent on parts.
Wysłane z mojego CPH2581 przy użyciu Tapatalka
RE: Bliss and CTA - marinalin85 - 01-06-2025
(01-05-2025, 10:22 AM)Sieluck Wrote: That's good news. However this retrofit, still being considered, will be very expensive to install. I'm not sure if this feature is actually worth the money that need to be spent on parts.
Wysłane z mojego CPH2581 przy użyciu Tapatalka
It is very expensive, retrofit or factory
But both are worth the money
RE: Bliss and CTA - suprnowa - 01-14-2025
Can I code BLIS using Orbit even if I bought used blis modules?
RE: Bliss and CTA - paunionutz - 01-15-2025
(01-14-2025, 11:19 PM)suprnowa Wrote: Can I code BLIS using Orbit even if I bought used blis modules?
Yed. I install used mofules from v60