+- OrBit Forums (https://forums.spaycetech.com)
+-- Forum: Diagnostics and Maintenance (https://forums.spaycetech.com/forumdisplay.php?fid=21)
+--- Forum: Service Functions (https://forums.spaycetech.com/forumdisplay.php?fid=22)
+--- Thread: Car not responding (/showthread.php?tid=1126)
Car not responding - kilmak - 12-06-2025
One week ago changed some configuration in Volvo xc60 2018:
-turned on ACC with pilot assist via config wizard to level 2
-turned on CarPlay and Android auto
-271 Start/stop memory to button with memory
-374 polestar level to 02 polestar optimization
-168 screen themes to 05 polestar (didn’t work)
After 2 days when I entered a car - both screens were not working and nothing happened when trying to start a car.
Doors, lighting, etc working, but I can not start the car
OrBit could not connect to CEM
Attaching DTCs what OrBit can find
OrBit DTC Report for YV1UZ68BCJ1032007 (last read: 2025/12/05 09:24:44)
BCM-U210856 - 2025/12/05 09:24:53
Adaptive Cruise Control- System Programming Failures- Invalid / incompatible configuration
Test failed
Test failed this monitoring/operational cycle
Pending DTC
Confirmed DTC
Test failed since last clear
BCM-U230054 - 2025/12/05 09:24:53
Central Configuration- System Programming Failures- Missing calibration
Test failed
Test failed this monitoring/operational cycle
Pending DTC
Confirmed DTC
Test failed since last clear
DIM-U2C8E86 - 2025/12/05 09:25:01
Invalid Data Received in ChdLockgProtnStsToHmi- Bus Signal / Message Failures- Signal invalid
Test failed
Test failed this monitoring/operational cycle
Pending DTC
Confirmed DTC
Test failed since last clear
DIM-U2C8F86 - 2025/12/05 09:25:01
Invalid Data Received in WiprSysFailrDetdSafe- Bus Signal / Message Failures- Signal invalid
Test failed
Test failed this monitoring/operational cycle
Pending DTC
Confirmed DTC
Test failed since last clear
DIM-U2C9086 - 2025/12/05 09:25:01
Invalid Data Received in CrashUnlckFailrSts- Bus Signal / Message Failures- Signal invalid
Test failed
Test failed this monitoring/operational cycle
Pending DTC
Confirmed DTC
Test failed since last clear
RE: Car not responding - jos - 12-06-2025
Uh, this sounds bad. I really hope this isn’t related to Orbit, even if it might look that way to you.
I can’t help with the actual issue, but it does seem strange that the problem showed up two days after making those config changes.
Did you read the config and the DTCs again after you made your adjustments? There were no errors before?
I think your car should be a Sensus, right? I’m just about to do my very first flash with similar settings, but I’m on an AAOS S60 from 2023.
Did you try every dumb suggestion an AI might give you for your specific model and year?
I just tried it for fun, and a bunch of things came up—just guessing though.
Are you sure your battery is good?
There isn’t even a beep when you don’t press the brake and try to start?
Any sounds at all coming from anything? (I don't mean Homer's DUH!)
RE: Car not responding - x119 - 12-07-2025
BCM - Battery Control Module
DIM - Driver display
Sure your battery isn't low?
I'd charge it - disconnect the battery for a bit - then see what happens on next system boot up.
RE: Car not responding - kilmak - 12-07-2025
(12-07-2025, 06:59 PM)x119 Wrote: BCM - Battery Control Module
DIM - Driver display
Sure your battery isn't low?
I'd charge it - disconnect the battery for a bit - then see what happens on next system boot up.
Already tried to disconnect battery for 10 minutes, for 30 and for 2 hours. Nothing. Battery ~12V
RE: Car not responding - x119 - 12-07-2025
I’d try the BCM bottom connector, disconnect for 15 mins. Disconnect battery in boot also.
Then try and reconnect OrBit, clear DTC. Restore OEM.
Shoot support(at)spaycetech.com a mail also.
RE: Car not responding - kilmak - 12-08-2025
Just sent my car to dealer service. Before that I couldn’t restore car back to stock because CEM was not responding. Is there any chance I can get blocked and dealer will not be able to solve my problem, if for example they will need to replace some block?