+- OrBit Forums (https://forums.spaycetech.com)
+-- Forum: Configuration Items (https://forums.spaycetech.com/forumdisplay.php?fid=3)
+--- Forum: Retrofitting (https://forums.spaycetech.com/forumdisplay.php?fid=13)
+--- Thread: Adding motion / tilt sensors to CMA vehicles (/showthread.php?tid=217)
Pages:
1
2
RE: Adding motion / tilt sensors to CMA vehicles - IMAY2023 - 03-08-2024
(03-07-2024, 01:20 PM)Muss Wrote: Hello. My car ,2019 XC40 D3 MOMENTUM FWD, came without an alarm, without IMS and without BBS. I purchased sh IMS and activated (65- 02interior movement sensor) with car horn and works . When I wanted to install the BBS (siren with inclination sensor 31652494), I couldn't find the connection plug. At IMS, there was a connection plug in the ceiling light.
Where can I find the BBS connection plug or do I have to draw wires?
Has anyone encountered this problem? How did you solve it?
Thank you
Have a look at this
https://accessories.volvocars.com/en-us/InstallationInstruction/Document/VCC-451816-7/XC40/2019/T4/Automatic/default/XC40%202019%20L.H.D
Good luck
Adding motion / tilt sensors to CMA vehicles - Muss - 03-17-2024
I follow that instructions and all is done only the jack connector isn't there. I can't find it in n space where is the siren. It's hidden in other space?
MY19 XC40 D3 MOMENTUM FWD
RE: Adding motion / tilt sensors to CMA vehicles - IMAY2023 - 03-18-2024
In S60 the cable is under the windshield washer water tank. Maybe same as the XC 40.
When I install the alarm sensor, the connector wasn't right under the cover, it was put deeper under the top cover.
Adding motion / tilt sensors to CMA vehicles - Muss - 03-18-2024
Excuse me for bothering you. Are you saying that under this wiper water tank I can find the cable with the connector for the siren? I looked but nothing on the surface.
MY19 XC40 D3 MOMENTUM FWD
RE: Adding motion / tilt sensors to CMA vehicles - IMAY2023 - 03-18-2024
No problem,
You are right, on S60 it was under the wiper water tank at the top left corner. (driver side) but yours is xc40.
According to official guide above, the connector should be under the plastic cover next to the place where you connect the siren.
Check near under the wiper motor, break booster. Volvo wouldn't just leave it unsecured, it might be connected to dead end connector on the firewall.
RE: Adding motion / tilt sensors to CMA vehicles - Aliaksandr - 08-23-2024
How to activate the siren in OrBit ?
RE: Adding motion / tilt sensors to CMA vehicles - IMAY2023 - 08-23-2024
(03-07-2024, 01:20 PM)Muss Wrote: Hello. My car ,2019 XC40 D3 MOMENTUM FWD, came without an alarm, without IMS and without BBS. I purchased sh IMS and activated (65- 02interior movement sensor) with car horn and works . When I wanted to install the BBS (siren with inclination sensor 31652494), I couldn't find the connection plug. At IMS, there was a connection plug in the ceiling light.
Where can I find the BBS connection plug or do I have to draw wires?
Has anyone encountered this problem? How did you solve it?
Thank you
It's in the engine bay! There you go.
(08-23-2024, 08:05 AM)Aliaksandr Wrote: How to activate the siren in OrBit ?
064 ALARM > 02 ALARM
RE: Adding motion / tilt sensors to CMA vehicles - Aliaksandr - 09-29-2024
After installing the siren, an error appeared. Battery Backed-up Sounder. System Internal Failures. Incorrect component installed.
When I lock the car I hear a beep. With this error.
Maybe because I didn't install IMS?
Will this work? 03 With alarm using vehicle horn
RE: Adding motion / tilt sensors to CMA vehicles - Aliaksandr - 10-02-2024
No ideas?
03 With alarm using vehicle horn - does not work.
04 With alarm for the Netherlands - What does it mean?
RE: Adding motion / tilt sensors to CMA vehicles - Aliaksandr - 11-05-2024
CEM:
B109A- Battery Backed-up Sounder BBS- System Internal
Failures-Incorrect component installed